TID codes John Deere Error - Page 2 of 3 - John Deere News & Innovations: Equipment, Technology, Solutions

TID codes

Understanding John Deere TID Fault Codes: Essential Information and Common Errors

John Deere TID Fault Codes are critical for diagnosing and maintaining the health of your John Deere machinery. These codes are part of the TID control software used in the activation of the transmission enable function within the DirectDrive transmission system. The TID and PTD control units manage the proportional solenoid valves for the forward clutch and reverse brake, ensuring smooth and efficient gear shifting.

Where Do TID Fault Codes Occur?

TID error codes are generated in various parts of the vehicle control system, including:

Come-home connector position
Operator presence detection
Reverse drive lever position
Park lock solenoid status (DirectDrive transmission)
Clutch pedal potentiometer position
Shift unit position
Engine speed monitoring
Vehicle speed monitoring

Common John Deere TID Diagnostic Trouble Codes

TID 002000.09 – Incorrect CAN Bus Message, Information from ECU Control Software
- Description: Data transfer problem between ECU control software and TID control software.
- Location: CAN Bus communication lines.
- Reaction: Limited or no function of the transmission.
TID 002820.31 – Operator Presence System, Fault
- Description: Operator not seated during operation of reverse drive lever.
- Location: Operator presence detection system.
- Reaction: Transmission shifting is not possible.
TID 520872.02 – Control Software, Internal Error
- Description: Error reading the internal module (EEPROM).
- Location: EEPROM module in the control software.
- Reaction: Limited or no function of the transmission.
TID 524230.06 – Transmission Enable Circuit, Current Too High
- Description: Excessive current detected in the transmission enable circuit, indicating a short circuit.
- Location: Transmission enable circuit.
- Reaction: Transmission enable function may fail to operate correctly.
TID 524254.04 – Transmission Enable Circuit, Voltage Too Low
- Description: Insufficient voltage in the transmission enable circuit when activation is required.
- Location: Transmission enable circuit.
- Reaction: Transmission enable function may fail to operate correctly.

Importance of John Deere TID Error Codes

Understanding and addressing John Deere TID error codes promptly is essential for maintaining the functionality and safety of your equipment. Regularly monitoring these codes can help prevent minor issues from escalating into major problems, ensuring your machinery operates smoothly and efficiently.

For optimal performance and longevity of your John Deere machinery, familiarize yourself with common TID fault codes and ensure regular maintenance checks. Properly addressing these codes can significantly reduce downtime and enhance the operational efficiency of your equipment.

TID 520958.31 – INFORMATION FOR OPERATOR: Shifting Transmission Not Permitted, Maximum Travel Speed Will Be Exceeded
John Deere TID codes
This error code, TID 520958.31, indicates that shifting the transmission is not permitted because the maximum travel speed set on the CommandCenter™ will be exceeded. This is a safety measure to ensure that the vehicle does not exceed its designated…
READ MORE
TID 520958.14 – INFORMATION FOR OPERATOR: Shifting Transmission Not Permitted
John Deere TID codes
This error code, TID 520958.14, is generated when the control software detects that shifting the transmission to the selected range is not permitted because another control software has commanded a limitation of travel speed. This is typically a safety feature…
READ MORE
TID 520872.02 – Control Software, Internal Error
John Deere TID codes
This error code, TID 520872.02, indicates an internal error in the control software related to the EEPROM module. The control software detects a problem reading data from the EEPROM, which can be caused by data corruption, hardware malfunction, or other…
READ MORE
TID 520871.02 – Control Software, Internal Error
John Deere TID codes
This error code, TID 520871.02, indicates an internal error in the control software related to the EEPROM module. Similar to TID 520870.02, this error occurs when the control software encounters a problem reading data from the EEPROM.
READ MORE
TID 520870.02 – Control Software, Internal Error
John Deere TID codes
This error code, TID 520870.02, is generated when the control software detects an error reading the internal module (EEPROM). EEPROM errors can occur due to data corruption, hardware malfunctions, or other internal issues.
READ MORE
TID 002820.31 – Operator Presence System, Fault
John Deere TID codes
This error code, TID 002820.31, indicates a fault in the Operator Presence System. The system detects that the operator is not seated during the operation of the reverse drive lever. This could be a result of the operator standing up…
READ MORE
TID 002161.09 – Incorrect CAN Bus Message, Information from SV1 Control Software
John Deere TID codes
This error code, TID 002161.09, is triggered when the control software detects a data transfer problem between the TID control software and the SV1 control software. The intermittent or non-existent reception of messages from the SV1 control software indicates potential…
READ MORE
TID 002145.09 – Incorrect CAN Bus Message, Information from FCC Control Software
John Deere TID codes
This error code, TID 002145.09, is generated when the control software detects a data transfer problem between the TID control software and the FCC control software. The reception of messages sent on the CAN Bus by the FCC control software…
READ MORE
TID 002140.09 – Incorrect CAN Bus Message, Information from AIC Control Software
John Deere TID codes
This error code, TID 002140.09, indicates a data transfer problem between the TID control software and the AIC control software. The messages sent on the CAN Bus by the AIC control software are received intermittently or not at all. This…
READ MORE
TID 002071.09 – Incorrect CAN Bus Message, Information from CCU Control Software
John Deere TID codes
This error code, TID 002071.09, is triggered when the control software detects a data transfer issue between the TID control software and the CCU control software. The intermittent or non-existent reception of messages from the CCU control software suggests an…
READ MORE
TID 002049.09 – Incorrect CAN Bus Message, Information from OIC Control Software
John Deere TID codes
This error code, TID 002049.09, is generated when there is a data transfer problem between the TID control software and the OIC control software. Intermittent or non-existent reception of messages from the OIC control software indicates potential issues such as…
READ MORE

John Deere News & Innovations: Equipment, Technology, Solutions

TID codes

Understanding John Deere TID Fault Codes: Essential Information and Common Errors

Where Do TID Fault Codes Occur?

Common John Deere TID Diagnostic Trouble Codes

Importance of John Deere TID Error Codes

TID 520958.31 – INFORMATION FOR OPERATOR: Shifting Transmission Not Permitted, Maximum Travel Speed Will Be Exceeded

TID 520958.14 – INFORMATION FOR OPERATOR: Shifting Transmission Not Permitted

TID 520872.02 – Control Software, Internal Error

TID 520871.02 – Control Software, Internal Error

TID 520870.02 – Control Software, Internal Error

TID 002820.31 – Operator Presence System, Fault

TID 002161.09 – Incorrect CAN Bus Message, Information from SV1 Control Software

TID 002145.09 – Incorrect CAN Bus Message, Information from FCC Control Software

TID 002140.09 – Incorrect CAN Bus Message, Information from AIC Control Software

TID 002071.09 – Incorrect CAN Bus Message, Information from CCU Control Software

TID 002049.09 – Incorrect CAN Bus Message, Information from OIC Control Software

Categories

Recent Posts

John Deere fault codes: