ETC codes John Deere Error - The Latest John Deere News and Trends

ETC codes

John Deere ETC Fault Codes / ETC Error Codes

John Deere ETC fault codes and ETC error codes are essential for diagnosing issues with the Electronic Temperature Control Unit (ETC) and the Electronic Transmission Control (ETC) in John Deere machinery. These codes help maintain optimal performance and longevity of the equipment by identifying specific problems within the system.

Electronic Temperature Control Unit (ETC)

Function: Controls the heater and air conditioning system (excluding automatic air conditioning).
Importance: Ensures effective climate control within the cab, enhancing operator comfort and productivity.

Electronic Transmission Control (ETC)

Focus: Manages automatic transmission functions.
Importance: Optimizes gear shifts and power output, crucial for the efficiency and durability of the machinery.

Common John Deere ETC Fault Codes

ETC 000168.03: Control Unit Supply Voltage Too High. Indicates excessive voltage in the control unit, potentially damaging sensitive components.
ETC 000168.04: Control Unit Supply Voltage Too Low. Indicates insufficient voltage, affecting control unit functionality.
ETC 000630.02: EEPROM Error in Control Unit. Data storage issue affecting control unit performance.
ETC 000639.14: High Error Rate on Vehicle CAN BUS. Indicates communication issues within the CAN BUS network, affecting data transmission.

Troubleshooting and Resolution

Diagnose Electrical Circuits: Check for short circuits, open circuits, and proper voltage levels.
Inspect Components: Test and replace faulty sensors, resistors, and control units.
Verify Connections: Ensure all wiring and connectors are secure and free from damage.
Update Software: Apply firmware updates to control units and related systems.

Importance of Regular Maintenance

Preventive Checks: Regular inspection and maintenance of the ETC system can prevent faults.
System Updates: Keeping software and firmware up to date ensures optimal performance and compatibility.

Understanding and addressing John Deere ETC fault codes and diagnostic trouble codes is crucial for the effective operation of your machinery. Regular maintenance, accurate diagnostics, and timely repairs help maintain the efficiency and durability of the equipment.

FCC 000158.17 – Instrument Unit, Supply Voltage (ELX) Too Low

John Deere ETC codes

This error code indicates that the supply voltage to the Instrument Unit (ELX) has fallen below 11.2 volts while the engine speed is below 500 RPM. This could be due to a weak battery, poor electrical connections, or issues with…
READ MORE
ETC 600006.13 – Diagnostic Trouble Code Not Known

John Deere ETC codes

The error code ETC 600006.13 is triggered by the CommandCenter (DTI) when it receives an ETC diagnostic trouble code via the CAN BUS that is not stored in the DTI memory. This “general” diagnostic trouble code enables the CommandCenter to…
READ MORE
ETC 524203.03 – Nonexistent Function Activated

John Deere ETC codes

The error code ETC 524203.03 is triggered when the control unit recognizes an open circuit when a nonexistent function is activated in address ETC026. This indicates an incorrect configuration or wiring issue.
READ MORE
ETC 523979.07 – S139 Switch for Heated Rear Window, Fault

John Deere ETC codes

The error code ETC 523979.07 is triggered when the control unit receives the engagement signal of the rear window heater switch (S139) for too long a period of time. This indicates that the switch is jammed, defective, or there is…
READ MORE
ETC 523979.05 – S139 Switch for Heated Rear Window, Current Too Low

John Deere ETC codes

The error code ETC 523979.05 is triggered when the control unit measures too low an amperage at the signal input of the indicator light in the rear window heater switch (S139, lead 2021). This indicates an interruption in the circuit…
READ MORE
ETC 523848.13 – B132 Adjusting Motor for Air Distribution, Not Calibrated

John Deere ETC codes

The error code ETC 523848.13 is triggered when the air distribution adjusting motor (B132) is found to have an invalid calibration or is not yet calibrated. Proper calibration of the adjusting motor is essential for accurate control and operation within…
READ MORE
ETC 523848.07 – B132 Adjusting Motor for Air Distribution, Fault

John Deere ETC codes

The error code ETC 523848.07 is triggered when the control unit receives a valid position signal from the potentiometer of the air distribution adjusting motor (B132), but the motor cannot be moved to its desired position via the motor’s connecting…
READ MORE
ETC 523848.06 – B132 Adjusting Motor for Air Distribution, Current Too High

John Deere ETC codes

The error code ETC 523848.06 is triggered when the control unit measures too high an amperage at adjusting motor connecting leads 2028 and/or 2029. This indicates a short to ground in the circuit.
READ MORE
ETC 523848.05 – B132 Adjusting Motor for Air Distribution, Current Too Low

John Deere ETC codes

The error code ETC 523848.05 is triggered when the control unit measures too low an amperage at adjusting motor connecting leads 2028 and/or 2029. This indicates that the circuit is open or shorted.
READ MORE
ETC 523848.04 – B132 Adjusting Motor for Air Distribution (Potentiometer), Voltage Too Low

John Deere ETC codes

The error code ETC 523848.04 is triggered when the control unit measures 0 volts at the signal input of the potentiometer for the position of the air distribution flaps (adjusting motor B132 for air distribution, lead 2017). This indicates a…
READ MORE
ETC 523848.03 – B132 Adjusting Motor for Air Distribution (Potentiometer), Voltage Too High

John Deere ETC codes

The error code ETC 523848.03 is triggered when the control unit measures a voltage in excess of 5 volts at the signal input of the potentiometer for the position of the air distribution flaps (adjusting motor B132 for air distribution,…
READ MORE

The Latest John Deere News and Trends

ETC codes

John Deere ETC Fault Codes / ETC Error Codes

Electronic Temperature Control Unit (ETC)

Electronic Transmission Control (ETC)

Common John Deere ETC Fault Codes

Troubleshooting and Resolution

Importance of Regular Maintenance

FCC 000158.17 – Instrument Unit, Supply Voltage (ELX) Too Low

ETC 600006.13 – Diagnostic Trouble Code Not Known

ETC 524203.03 – Nonexistent Function Activated

ETC 523979.07 – S139 Switch for Heated Rear Window, Fault

ETC 523979.05 – S139 Switch for Heated Rear Window, Current Too Low

ETC 523848.13 – B132 Adjusting Motor for Air Distribution, Not Calibrated

ETC 523848.07 – B132 Adjusting Motor for Air Distribution, Fault

ETC 523848.06 – B132 Adjusting Motor for Air Distribution, Current Too High

ETC 523848.05 – B132 Adjusting Motor for Air Distribution, Current Too Low

ETC 523848.04 – B132 Adjusting Motor for Air Distribution (Potentiometer), Voltage Too Low

ETC 523848.03 – B132 Adjusting Motor for Air Distribution (Potentiometer), Voltage Too High

Categories

Recent Posts

John Deere fault codes: