John Deere fault codes John Deere error - Page 172 of 349 - John Deere News & Innovations: Equipment, Technology, Solutions

John Deere fault codes

PTA 000161.03 – Sensor for Transmission Input Speed, Voltage Too High
John Deere error PTA codes
This diagnostic trouble code is generated when the PTA control software detects that the voltage at the signal input of the transmission input speed sensor is too high. This condition indicates that the sensor circuit is open or shorted to a positive lead in the sensor circuit.
READ MORE
PTA 000161.02 – Sensor for Transmission Input Speed, Speed Drop Not Plausible
John Deere error PTA codes
This diagnostic trouble code is generated when the PTA control software detects that the transmission input speed has suddenly dropped to 0 rpm, which is not a plausible scenario under normal operating conditions.
READ MORE
PTA 000161.00 – Sensor for Transmission Input Speed, Speed Too High
John Deere error PTA codes
This diagnostic trouble code is generated when the PTA control software detects that the transmission input speed is too high. It indicates excessive speed, particularly when there is no weight pushing from behind to justify it. This may be a sign of a fault in the speed sensor or the control software.
READ MORE
PTA 000127.01 – Transmission Oil Pressure Switch, Oil Pressure Too Low
John Deere error PTA codes
This diagnostic trouble code is generated when the PTA control software cannot determine the transmission oil pressure (system pressure). The transmission oil pressure switch opens when the transmission input speed exceeds 900 rpm, indicating low oil pressure.
READ MORE
PTA 000126.00 – Transmission Oil Filter Pressure Switch, Filter Restricted
John Deere error PTA codes
This diagnostic trouble code is generated when the PTA control software detects that the transmission oil filter is restricted. The pressure switch of the transmission oil filter opens when the transmission oil temperature exceeds 40°C (104°F), indicating a potential restriction in the filter.
READ MORE
PL4 516398.05 – Park Lock Solenoid 2 (DirectDrive Transmission), Current Too Low
John Deere error PL4 codes
This error code is generated if the control software detects that the current value at the Park Lock Solenoid 2 is too low. This may indicate an open circuit.
READ MORE
PL4 002192.09 (PL4 2192.09) – Incorrect CAN Bus Message, Information from PL3 Control Software
John Deere error PL4 codes
This error code is generated when there is a data transfer problem between the PL4 control software and the PL3 control software. The reception of messages sent on the CAN Bus by the PL3 control software is intermittent or non-existent. This typically indicates an open circuit in the CAN Bus, a short circuit, or faulty…
READ MORE
PL4 002191.09 (PL4 2191.09) – Incorrect CAN Bus Message, Information from PL2 Control Software
John Deere error PL4 codes
This error code is generated when there is a data transfer problem between the PL4 control software and the PL2 control software. The reception of messages sent on the CAN Bus by the PL2 control software is intermittent or non-existent. This typically indicates an open circuit in the CAN Bus, a short circuit, or faulty…
READ MORE
PL4 002190.09 (PL4 2190.09) – Incorrect CAN Bus Message, Information from PL1 Control Software
John Deere error PL4 codes
This error code is generated when there is a data transfer problem between the PL4 control software and the PL1 control software. The reception of messages sent on the CAN Bus by the PL1 control software is intermittent or non-existent. This typically indicates an open circuit in the CAN Bus, a short circuit, or faulty…
READ MORE
PL4 002168.09 (PL4 2168.09) – Incorrect CAN Bus Message, Information from PL3 Control Software
John Deere error PL4 codes
This error code is triggered when there is a data transfer problem between the PL4 control software and the PL3 control software. The reception of messages sent on the CAN Bus by the PL3 control software is intermittent or non-existent. This typically indicates an open circuit in the CAN Bus, a short circuit, or faulty…
READ MORE
PL4 002167.09 (PL4 2167.09) – Incorrect CAN Bus Message, Information from PL2 Control Software
John Deere error PL4 codes
This error code is triggered when there is a data transfer problem between the PL4 control software and the PL2 control software. The reception of messages sent on the CAN Bus by the PL2 control software is intermittent or non-existent. This typically indicates an open circuit in the CAN Bus, a short circuit, or faulty…
READ MORE

John Deere News & Innovations: Equipment, Technology, Solutions

John Deere fault codes

PTA 000161.03 – Sensor for Transmission Input Speed, Voltage Too High

PTA 000161.02 – Sensor for Transmission Input Speed, Speed Drop Not Plausible

PTA 000161.00 – Sensor for Transmission Input Speed, Speed Too High

PTA 000127.01 – Transmission Oil Pressure Switch, Oil Pressure Too Low

PTA 000126.00 – Transmission Oil Filter Pressure Switch, Filter Restricted

PL4 516398.05 – Park Lock Solenoid 2 (DirectDrive Transmission), Current Too Low

PL4 002192.09 (PL4 2192.09) – Incorrect CAN Bus Message, Information from PL3 Control Software

PL4 002191.09 (PL4 2191.09) – Incorrect CAN Bus Message, Information from PL2 Control Software

PL4 002190.09 (PL4 2190.09) – Incorrect CAN Bus Message, Information from PL1 Control Software

PL4 002168.09 (PL4 2168.09) – Incorrect CAN Bus Message, Information from PL3 Control Software

PL4 002167.09 (PL4 2167.09) – Incorrect CAN Bus Message, Information from PL2 Control Software

Categories

Recent Posts

John Deere fault codes: