XSC codes John Deere Error - Page 2 of 8 - John Deere News & Innovations: Equipment, Technology, Solutions

XSC codes

Comprehensive Guide to John Deere XSC Error Codes and Fault Codes

The John Deere XSC control software, integrated within the AutoTrac™ automatic steering system, plays a critical role in managing the vehicle’s steering functions. Working alongside the XMC control software, it processes signals from various sensors and modules to ensure precise and efficient steering. Below is a detailed list of common John Deere XSC fault codes and their descriptions to help diagnose and resolve issues effectively.

John Deere XSC Fault Codes List

Understanding the XSC diagnostic trouble codes is essential for maintaining the optimal performance of the AutoTrac™ system. Here are some of the most frequently encountered fault codes:

1. XSC 523824.16 – Steering Wheel Position Sensor, Frequency at Channel 2 Too High

Description: This code indicates that the frequency at channel 2 of the steering wheel position sensor exceeds 300 Hz.
Occurrence: Detected in the steering control unit.
Impact: Limited or no function of the control unit.

2. XSC 523821.02 – Incompatible Harness on Steering Control Unit (AutoTrac™)

Description: Indicates that the control unit is connected to an incorrect harness.
Occurrence: Detected during harness connection checks.
Impact: Limited or no function of the control software.

3. XSC 523826.00 – Wheel Angle Sensor Channel 1, Voltage Too High

Description: Voltage over 4.5V registered at channel 1 of the wheel angle sensor.
Occurrence: Detected in the wheel angle sensor channel.
Impact: Limited or no function of the control unit.

4. XSC 524055.12 – Control Software Internal Fault

Description: A fault occurs when the software is launched.
Occurrence: Detected during control software startup.
Impact: Limited or no function of the control software.

5. XSC 523925.09 – Incorrect CAN BUS Message, Information from XMC Control Software

Description: Data transfer problem between XMC and XSC control software due to intermittent or non-existent CAN messages.
Occurrence: Detected in the CAN BUS network.
Impact: Limited or no function of the control software.

Key Components and Signal Processing

The XSC control software receives and processes signals from:

Steering Wheel Position Sensor
Wheel Angle Sensor
LIN Bus Module (Shift Console)
LIN Bus Module (Position H)

These signals are compared with those of the XMC control software before transmitting to:

Solenoid Valve for Steering Control Valve (Enable Valve)
Solenoid Valve for Steering Control Valve (Left Turn)
Solenoid Valve for Steering Control Valve (Right Turn)

Maintaining Optimal Performance

For optimal performance of the John Deere AutoTrac™ system, regularly monitor and address any XSC fault codes. Proper maintenance and timely resolution of these codes will ensure efficient and accurate steering control, enhancing the overall functionality of your equipment.

By understanding and utilizing this John Deere XSC diagnostic trouble codes list, you can effectively diagnose and troubleshoot issues within the AutoTrac™ system, ensuring reliable and precise operation.

XSC 523821.02 – Incompatible Harness on Steering Control Unit (AutoTrac™)
John Deere XSC codes
This error code, XSC 523821.02, indicates that the control unit is connected to an incorrect harness, which is incompatible with the steering control unit (AutoTrac™). This misconnection can lead to communication failures and improper operation of the steering system.
READ MORE
XSC 523815.06 – Steering Control Valve, Current Too High
John Deere XSC codes
This error code, XSC 523815.06, is generated when the current for the steering control valve (enable valve) is too high, indicating a short to ground. Excessive current can damage the valve and disrupt the steering control system.
READ MORE
XSC 523815.05 – Steering Control Valve, Current Too Low
John Deere XSC codes
This error code, XSC 523815.05, is generated when the current for the steering control valve (enable valve) is too low, indicating that the circuit is open. This low current can affect the proper functioning of the valve and the steering…
READ MORE
XSC 523815.04 – Steering Control Valve, Voltage Too Low
John Deere XSC codes
This error code, XSC 523815.04, is generated when the voltage for the steering control valve (enable valve) is too low, indicating a short to ground. This low voltage can affect the proper functioning of the valve and the steering control…
READ MORE
XSC 523815.03 – Steering Control Valve, Voltage Too High
John Deere XSC codes
This error code, XSC 523815.03, is generated when the voltage for the steering control valve (enable valve) is too high, indicating a short to 12 volts. This high voltage can affect the proper functioning of the valve and the steering…
READ MORE
XSC 523795.13 – Steering Control Valve Out of Calibration
John Deere XSC codes
This error code, XSC 523795.13, indicates that the steering control valve has an invalid calibration or is not yet calibrated. Proper calibration is necessary for the accurate and effective operation of the steering control system.
READ MORE
XSC 523795.07 – Steering Control Valve, Malfunction
John Deere XSC codes
This error code, XSC 523795.07, indicates that the steering control valve (enable valve) is sticking in its open position. This malfunction can lead to unresponsive or erratic steering control.
READ MORE
XSC 523789.13 – Steering Angle Sensor Not Calibrated
John Deere XSC codes
This error code, XSC 523789.13, indicates that the steering angle sensor has an invalid calibration or is not yet calibrated. Proper calibration is essential for accurate steering angle measurements and responsive steering control.
READ MORE
XSC 523789.05 – Wheel Angle Sensor, Open Circuit
John Deere XSC codes
This error code, XSC 523789.05, is generated when the XSC control software registers that the voltage at the output of the wheel angle sensor is too high. This condition indicates that the circuit is open, suggesting a potential issue with…
READ MORE
XSC 523219.04 – Control Software, Supply Voltage (BAT) Too Low
John Deere XSC codes
This error code, XSC 523219.04, indicates that the supply voltage (BAT) at pin J2M3 has dropped below 9 volts. This low voltage condition can affect the control software’s ability to function properly.
READ MORE
XSC 523218.04 – Control Software, Supply Voltage (BAT) Too Low
John Deere XSC codes
This error code, XSC 523218.04, indicates that the supply voltage (BAT) at pin J2M4 has dropped below 9 volts. This low voltage condition can affect the control software’s ability to function properly.
READ MORE

John Deere News & Innovations: Equipment, Technology, Solutions

XSC codes

Comprehensive Guide to John Deere XSC Error Codes and Fault Codes

John Deere XSC Fault Codes List

1. XSC 523824.16 – Steering Wheel Position Sensor, Frequency at Channel 2 Too High

2. XSC 523821.02 – Incompatible Harness on Steering Control Unit (AutoTrac™)

3. XSC 523826.00 – Wheel Angle Sensor Channel 1, Voltage Too High

4. XSC 524055.12 – Control Software Internal Fault

5. XSC 523925.09 – Incorrect CAN BUS Message, Information from XMC Control Software

Key Components and Signal Processing

Maintaining Optimal Performance

XSC 523821.02 – Incompatible Harness on Steering Control Unit (AutoTrac™)

XSC 523815.06 – Steering Control Valve, Current Too High

XSC 523815.05 – Steering Control Valve, Current Too Low

XSC 523815.04 – Steering Control Valve, Voltage Too Low

XSC 523815.03 – Steering Control Valve, Voltage Too High

XSC 523795.13 – Steering Control Valve Out of Calibration

XSC 523795.07 – Steering Control Valve, Malfunction

XSC 523789.13 – Steering Angle Sensor Not Calibrated

XSC 523789.05 – Wheel Angle Sensor, Open Circuit

XSC 523219.04 – Control Software, Supply Voltage (BAT) Too Low

XSC 523218.04 – Control Software, Supply Voltage (BAT) Too Low

Categories

Recent Posts

John Deere fault codes: