XSC codes John Deere Error - Page 4 of 8 - John Deere News & Innovations: Equipment, Technology, Solutions

XSC codes

Comprehensive Guide to John Deere XSC Error Codes and Fault Codes

The John Deere XSC control software, integrated within the AutoTrac™ automatic steering system, plays a critical role in managing the vehicle’s steering functions. Working alongside the XMC control software, it processes signals from various sensors and modules to ensure precise and efficient steering. Below is a detailed list of common John Deere XSC fault codes and their descriptions to help diagnose and resolve issues effectively.

John Deere XSC Fault Codes List

Understanding the XSC diagnostic trouble codes is essential for maintaining the optimal performance of the AutoTrac™ system. Here are some of the most frequently encountered fault codes:

1. XSC 523824.16 – Steering Wheel Position Sensor, Frequency at Channel 2 Too High

Description: This code indicates that the frequency at channel 2 of the steering wheel position sensor exceeds 300 Hz.
Occurrence: Detected in the steering control unit.
Impact: Limited or no function of the control unit.

2. XSC 523821.02 – Incompatible Harness on Steering Control Unit (AutoTrac™)

Description: Indicates that the control unit is connected to an incorrect harness.
Occurrence: Detected during harness connection checks.
Impact: Limited or no function of the control software.

3. XSC 523826.00 – Wheel Angle Sensor Channel 1, Voltage Too High

Description: Voltage over 4.5V registered at channel 1 of the wheel angle sensor.
Occurrence: Detected in the wheel angle sensor channel.
Impact: Limited or no function of the control unit.

4. XSC 524055.12 – Control Software Internal Fault

Description: A fault occurs when the software is launched.
Occurrence: Detected during control software startup.
Impact: Limited or no function of the control software.

5. XSC 523925.09 – Incorrect CAN BUS Message, Information from XMC Control Software

Description: Data transfer problem between XMC and XSC control software due to intermittent or non-existent CAN messages.
Occurrence: Detected in the CAN BUS network.
Impact: Limited or no function of the control software.

Key Components and Signal Processing

The XSC control software receives and processes signals from:

Steering Wheel Position Sensor
Wheel Angle Sensor
LIN Bus Module (Shift Console)
LIN Bus Module (Position H)

These signals are compared with those of the XMC control software before transmitting to:

Solenoid Valve for Steering Control Valve (Enable Valve)
Solenoid Valve for Steering Control Valve (Left Turn)
Solenoid Valve for Steering Control Valve (Right Turn)

Maintaining Optimal Performance

For optimal performance of the John Deere AutoTrac™ system, regularly monitor and address any XSC fault codes. Proper maintenance and timely resolution of these codes will ensure efficient and accurate steering control, enhancing the overall functionality of your equipment.

By understanding and utilizing this John Deere XSC diagnostic trouble codes list, you can effectively diagnose and troubleshoot issues within the AutoTrac™ system, ensuring reliable and precise operation.

XSC 522390.12 – Tractor-Implement Automation™, Fault
John Deere XSC codes
This error code, XSC 522390.12, is generated when no valid information from the implement is received via the implement CAN Bus. This indicates a potential problem in the CAN Bus network or the implement control software, affecting the data communication…
READ MORE
XSC 522390.11 – Tractor-Implement Automation™, Fault
John Deere XSC codes
This error code, XSC 522390.11, is generated when the come-home mode is activated on tractors with AutoPowr™/IVT™ transmission, leading to the deactivation of all functions of the Tractor Implement Automation™.
READ MORE
XSC 522390.09 – Incorrect CAN BUS Message, Information from Implement
John Deere XSC codes
This error code, XSC 522390.09, is generated when no valid information from the implement is received via the implement CAN Bus. This issue can be caused by problems in the CAN Bus network or issues with the implement control software.
READ MORE
XSC 522387.07 – Expected Steering Movement of Front Wheels is Not Detected
John Deere XSC codes
This error code, XSC 522387.07, is generated when the XSC control software commands a steering movement but fails to detect a corresponding signal from the wheel angle sensor (WAS), or if the received signal is too low. This can indicate…
READ MORE
XSC 003842.01 – Wheel Angle Sensor Channel 2, Voltage Too Low
John Deere XSC codes
This error code, XSC 003842.01, indicates that the voltage at channel 2 of the wheel angle sensor is below 0.25 volts. Despite this low voltage, the value measured by the XMC control software is within the acceptable range, suggesting a…
READ MORE
XSC 003842.00 – Wheel Angle Sensor Channel 2, Voltage Too High
John Deere XSC codes
This error code, XSC 003842.00, indicates that the voltage at channel 2 of the wheel angle sensor exceeds 2.25 volts. Despite this high voltage, the value measured by the XMC control software is within the acceptable range, suggesting a potential…
READ MORE
XSC 003841.01 – Wheel Angle Sensor Channel 1, Voltage Too Low
John Deere XSC codes
This error code, XSC 003841.01, indicates that a voltage below 0.5 volts is registered at channel 1 of the wheel angle sensor. Despite this low voltage, the value measured by the XMC control software is within the acceptable range, suggesting…
READ MORE
XSC 003841.00 – Wheel Angle Sensor Channel 1, Voltage Too High
John Deere XSC codes
This error code, XSC 003841.00, indicates that a voltage over 4.5 volts is registered at channel 1 of the wheel angle sensor. Despite this high voltage, the value measured by the XMC control software is within the acceptable range, suggesting…
READ MORE
XSC 003512.04 – 5-Volt Supply Voltage 2 Too Low
John Deere XSC codes
This error code, XSC 003512.04, indicates that the voltage supply to the 5-volt components has dropped below 4.75 volts. This condition suggests a short to ground or an internal fault within the control unit, which can disrupt normal operation and…
READ MORE
XSC 003512.03 – 5-Volt Supply Voltage 2 Too High
John Deere XSC codes
This error code, XSC 003512.03, indicates that the voltage supply to the 5-volt components has exceeded 5.25 volts. This condition typically suggests a short to 12 volts, which can damage the 5-volt components and disrupt normal operation.
READ MORE
XSC 003511.04 – 5-Volt Supply Voltage 1 Too Low
John Deere XSC codes
This error code, XSC 003511.04, indicates that the voltage supply to the 5-volt components has dropped below 4.75 volts. This condition suggests a short to ground or an internal fault within the control unit, which can disrupt normal operation and…
READ MORE

John Deere News & Innovations: Equipment, Technology, Solutions

XSC codes

Comprehensive Guide to John Deere XSC Error Codes and Fault Codes

John Deere XSC Fault Codes List

1. XSC 523824.16 – Steering Wheel Position Sensor, Frequency at Channel 2 Too High

2. XSC 523821.02 – Incompatible Harness on Steering Control Unit (AutoTrac™)

3. XSC 523826.00 – Wheel Angle Sensor Channel 1, Voltage Too High

4. XSC 524055.12 – Control Software Internal Fault

5. XSC 523925.09 – Incorrect CAN BUS Message, Information from XMC Control Software

Key Components and Signal Processing

Maintaining Optimal Performance

XSC 522390.12 – Tractor-Implement Automation™, Fault

XSC 522390.11 – Tractor-Implement Automation™, Fault

XSC 522390.09 – Incorrect CAN BUS Message, Information from Implement

XSC 522387.07 – Expected Steering Movement of Front Wheels is Not Detected

XSC 003842.01 – Wheel Angle Sensor Channel 2, Voltage Too Low

XSC 003842.00 – Wheel Angle Sensor Channel 2, Voltage Too High

XSC 003841.01 – Wheel Angle Sensor Channel 1, Voltage Too Low

XSC 003841.00 – Wheel Angle Sensor Channel 1, Voltage Too High

XSC 003512.04 – 5-Volt Supply Voltage 2 Too Low

XSC 003512.03 – 5-Volt Supply Voltage 2 Too High

XSC 003511.04 – 5-Volt Supply Voltage 1 Too Low

Categories

Recent Posts

John Deere fault codes: