John Deere fault codes John Deere error - Page 71 of 349 - John Deere News & Innovations: Equipment, Technology, Solutions

John Deere fault codes

SSU 000524.09 – Incorrect CAN BUS Message, Gear Selection from EPC
John Deere error SSU codes
This diagnostic trouble code (DTC), SSU 000524.09, is generated when the gear selection information from the Electronic Power Control (EPC) is not recognized on the CAN BUS. This indicates a communication issue between the EPC and the rest of the system.
READ MORE
SSU 000517.09 – Incorrect CAN BUS Message, Travel Speed from StarFire ITC Receiver
John Deere error SSU codes
This diagnostic trouble code (DTC), SSU 000517.09, is generated when the travel speed data placed on the ISOBUS by the StarFire ITC receiver cannot be read. This indicates a communication issue between the StarFire ITC receiver and the rest of the system.
READ MORE
SSU 000237.02 – Incorrect CAN BUS Message, Vehicle Identification Number (VIN) from BCU
John Deere error SSU codes
This diagnostic trouble code (DTC), SSU 000237.02, is generated when there is a data transfer problem between the Body Control Unit (BCU) and the SSU concerning the vehicle identification number (VIN). Reception of the CAN message regarding the VIN is intermittent or nonexistent, which could be due to a loose wire or other communication issues.
READ MORE
SSU 000177.09 – Incorrect CAN BUS Message, Hydraulic Oil Temperature from EPC or TCU
John Deere error SSU codes
This diagnostic trouble code (DTC), SSU 000177.09, is generated when the information on transmission oil temperature is not recognized on the CAN BUS after four attempts. AutoTrac requires the transmission oil temperature to be above 0°C to function, so this issue can disrupt AutoTrac operations.
READ MORE
SSU 000168.04 – Supply Voltage Too Low
John Deere error SSU codes
This diagnostic trouble code (DTC), SSU 000168.04, is triggered if the battery voltage drops below 9 volts for longer than 320 milliseconds. This indicates an undervoltage condition that can affect the performance and reliability of the equipment’s electrical systems.
READ MORE
SSU 000168.03 – Supply Voltage Too High
John Deere error SSU codes
This diagnostic trouble code (DTC), SSU 000168.03, is triggered if the battery voltage rises above 16 volts for longer than 320 milliseconds. This indicates an overvoltage condition that can be harmful to the electrical components of the equipment.
READ MORE
SSU 000162.09 – Incorrect CAN BUS Message, Transmission Type from EPC or TCU
John Deere error SSU codes
This diagnostic trouble code (DTC), SSU 000162.09, is generated when the information on transmission type (entry in address SSU 036) is not recognized on the CAN BUS after four attempts. This indicates a communication issue with the CAN BUS, specifically between the Electronic Power Control (EPC) or Transmission Control Unit (TCU) and the Body Control…
READ MORE
SSU 000084.09 – Incorrect CAN BUS Message, Travel Speed from BCU
John Deere error SSU codes
This diagnostic trouble code (DTC), SSU 000084.09, is generated when no signal from the travel speed sending unit can be detected on the CAN BUS. This indicates an issue with the communication between the travel speed sending unit and the BCU (Body Control Unit).
READ MORE
SIC 600006.31 – Diagnostic Trouble Code Not Known
John Deere error SIC codes
This diagnostic trouble code, SIC 600006.31, is triggered by the CommandCenter (DTI) when the DTI receives a SIC diagnostic trouble code via the CAN BUS that is not stored in the DTI memory. This “general” diagnostic trouble code enables the CommandCenter (DTI) to display information relating to this unknown SIC diagnostic trouble code.
READ MORE
SIC 524087.14 – INFORMATION FOR OPERATOR: Selection for Front Loader Attachment or Front-End Implements Changed
John Deere error SIC codes
This operator information (diagnostic trouble code) is generated when a change has been made in address SIC 041 or in the DTI (display terminal interface) to select the front loader or front-end implement. This address is used to preselect front loader or implement.
READ MORE
SIC 523898.31 – S99 Control Lever (Potentiometer or Switch) for ESCV 4, Faulty
John Deere error SIC codes
This error code, SIC 523898.31, is saved if the potentiometer signal voltage of the ESCV 4 (Electro-Hydraulic Section Control Valve) control lever is not to specification, or if the status of the switch on the control lever does not correspond to the signal voltage of the potentiometer.
READ MORE

John Deere News & Innovations: Equipment, Technology, Solutions

John Deere fault codes

SSU 000524.09 – Incorrect CAN BUS Message, Gear Selection from EPC

SSU 000517.09 – Incorrect CAN BUS Message, Travel Speed from StarFire ITC Receiver

SSU 000237.02 – Incorrect CAN BUS Message, Vehicle Identification Number (VIN) from BCU

SSU 000177.09 – Incorrect CAN BUS Message, Hydraulic Oil Temperature from EPC or TCU

SSU 000168.04 – Supply Voltage Too Low

SSU 000168.03 – Supply Voltage Too High

SSU 000162.09 – Incorrect CAN BUS Message, Transmission Type from EPC or TCU

SSU 000084.09 – Incorrect CAN BUS Message, Travel Speed from BCU

SIC 600006.31 – Diagnostic Trouble Code Not Known

SIC 524087.14 – INFORMATION FOR OPERATOR: Selection for Front Loader Attachment or Front-End Implements Changed

SIC 523898.31 – S99 Control Lever (Potentiometer or Switch) for ESCV 4, Faulty

Categories

Recent Posts

John Deere fault codes: